More products out of our product range

• Designed for rugged environment 
• Completely sealed (IP67 rating)
• 3 drive positions, forward - neutral - reverse
• With wiring harness (length 100mm) and DEUTSCH Connector
• Fits on steering column size 38, 45 and 55mm
• with locating pin
• Operating voltage range: 1 to 48 V
• Solenoid load 3 A @ 12.8 Volt with arc suppression

Remote control unit for hydraulic power packs consisting of:

Data receiver:

• Number of outputs: 2
• Frequency bands: ISM 868/915 MHz
• Protection class: IP67
• Nominal supply 12/24VDC (10 - 30 VDC permitted)

Handheld:

• Number of controls: 2
• Battery supply by 2 batteries type AAA 1, 5V
• Range in open field: 100 - 150 m
• Silicone rubber keyboard (protection class IP67)

- 16 programmable setpoints
- 16 programmable ramp times or four quadrant ramp
- Smooth ramp generation
- Simple and intuitive parameterization of the analog input
- Analog input and digital setpoints can be linked via the following functions: * , / , + , - , min and max
- Parameters for valve adaptation (MIN, MAX, POL)- Coverage jump or kinked gain characteristic
- Fault diagnostics and extended function check
- Simplified parameterization with WPC-300 software

- Power amplifier for proportional valves in a DIN EN 175 301-803 A connector housing
- Digital reproducible settings- Free scalability of the input signal
- Can also be used as soft switch amplifier (soft switching on and off)
- M12 plug
- Programmable via USB/LIN bus
- Free parameterization of ramps, MIN and MAX, dither (frequency, amplitude) and PWM frequency
- Parameter settings via integrated keys and a selector switch (functionally reduced compared to the USB / LIN bus)
- Optional: Version with Can-Bus on demand - output current 1 A / 2.5 A
- Adaptable to all standard proportional valves

- Swing angle, pressure and power control
- Freely scalable analog inputs
- Compact design
- Digital reproducible adjustment
- Optimized control function
- Application-oriented parameterization
- Two parameter sets can be selected for pressure control
- Swivel angle limiting function
- Integrated power output stage
- Alternatively, analog manipulated variable for control valves with OBE
- Fault diagnostics and extended function check
- Easy parameterization with the WPC-300 software

- Power amplifier for proportional valves in a DIN EN 175 301-803 A connector housing
- Digital reproducible settings
- Free scalability of the input signal
- Can also be used as soft switch amplifier (soft switching on and off)
- M12 plug
- Programmable via USB/LIN bus
- Free parameterization of ramps, MIN and MAX, dither (frequency, amplitude) and PWM frequency
- Parameter settings via integrated keys and a selector switch (functionally reduced compared to the USB / LIN bus)
- Optional: Version with Can-Bus on request
- Output current 1 A / 2.5 A
- Adaptable to all standard proportional valves

- Power amplifier for proportional valves in a DIN EN 175 301-803 A connector housing
- I/O - Link Port Class B, with internal galvanic isolation of the additional supply voltage
- complies with specification V1.1, data rate COM3 = 230.4 kBaud
- Digital, reproducible settings
- Can also be used as soft switch amplifier (soft switching on and off)
- M12 plug
- Parameterizable via I/O - Link
- Free adjustment of ramps, MIN and MAX, dither (frequency, amplitude) and PWM frequency
- Output current up to max. 2.5 A, parameterizable
- Adaptable to all standard proportional valves

- General power amplifier, one module for all applications
- GL Certification
- Control of directional valves or two pressure or throttle valves- Analogue or digital inputs
- Compact housing
- Digitally reproducible settings
- Free scaling of the analog inputs
- Monitoring of the input signal (for e.g. joystick)
- Characteristic linearization via 10 XY points per direction
- Free parameterization of RAMP, MIN / MAX, output current and DITHER (frequency, amplitude) - Range of nominal output current: 0.5 ... 2.6 A
- Simple and application-oriented parameterization with WPC software
- Fault diagnostics and extended function check

- Power amplifier for proportional valves 0...10V Input
- Printed circuit board in IP-65 housing
- Digital reproducible settings
- Free scalability of the input signal
- Reference voltage for supply of potentiometers
- Free parameterization of ramps, MIN and MAX, dither (frequency, amplitude) and PWM frequency
- Output current 1 A and 2.5 A
- Simple and application-oriented parameter setting
- Error monitoring and extended functional checks
- Programmable via USB/LIN bus, easy parameterization with the WPC-300 software
- Parameter settings via integrated keys and a selector switch (functionally reduced compared to the USB / LIN bus)
- Adaptable to all standard proportional valves

- Power amplifier for proportional valves with 4...20 mA Input
- Printed circuit board in IP-65 housing
- Digital reproducible settings
- Free scalability of the input signal
- Reference voltage for supply of potentiometers
- Free parameterization of ramps, MIN and MAX, dither (frequency, amplitude) and PWM frequency
- Output current 1 A and 2.5 A
- Simple and application-oriented parameter setting
- Error monitoring and extended functional checks
- Programmable via USB/LIN bus, easy parameterization with the WPC-300 software
- Parameter settings via integrated keys and a selector switch (functionally reduced compared to the USB / LIN bus)
- Adaptable to all standard proportional valves

- Swing angle, pressure and power control
- Freely scalable analog inputs
- Compact design
- Digital reproducible adjustment
- Optimized control function
- Application-oriented parameterization
- Two parameter sets can be selected for pressure control
- Swivel angle limiting function
- Integrated power output stage
- Alternatively, analog manipulated variable for control valves with OBE
- Fault diagnostics and extended function check
- Easy parameterization with the WPC-300 software